Here’s a highly simplified explanation of mic specs in plain English. It may help you evaluate microphones based on their specifications.
TYPE: Condenser, dynamic or ribbon.
These terms refer to the way the microphone converts sound into an electrical signal. Each type has its own “sound” and application.
- Condenser: High-fidelity, detailed sound with lots of clean high frequencies. Popular for studio vocals, stage vocals, acoustic instruments and cymbals. Requires “phantom power” from a mixer to operate. Can be miniaturized.
- Dynamic: Good sound quality, rugged. Popular for guitar amps and drums. Does not require phantom power.
- Ribbon: Warm, smooth sound quality. Delicate. Popular for horns and guitar amps. Does not require phantom power.
FREQUENCY RESPONSE: The lowest and highest frequencies that the mic can pick up well.
A frequency response from 20 Hz to 20,000 Hz covers all the frequencies we can hear. 80 Hz to 15,000 Hz is adequate for most instruments and vocals. 40 Hz to 10 kHz is adequate for bass instruments.
Proximity effect: Most microphones boost the bass when used up close. That adds a warm, full tone quality. Microphones with an omnidirectional polar pattern do not have proximity effect.
Also called directional pickup pattern. It’s a graph of how the mic picks up sounds coming from different directions.
- Cardioid: Picks up best in front of the mic. Partly rejects sounds approaching the sides or rear of the mic. Rejects sound best toward the rear.
- Supercardioid: Picks up best in front of the mic. Partly rejects sounds approaching the sides or rear of the mic. “Tighter” or more narrow pickup than cardioid.
- Hypercardioid: Picks up best in front of the mic. Partly rejects sounds approaching the sides or rear of the mic. “Tighter” or more narrow pickup than supercardioid.
- Omnidirectional or omni: Picks up equally well in all directions. Unlike the other patterns, omni has no proximity effect (no up-close bass boost).
- Bidirectional or figure-8: Picks up best in two directions — in front of and behind the mic — and rejects sounds to the sides.
Use cardioid, supercardioid, hypercardioid, bidirectional, or an instrument-mounted omni when you want to reject background noise, room acoustics and feedback. A mic with one of those patterns tends to pick up mostly what it is aiming at, and not so much of everything else. Use omnidirectional when you want to pick up everything around the microphone.
IMPEDANCE: An electrical characteristic of a microphone. Use low-impedance microphones (under 300 ohms) to prevent hum pickup if you use mic cables over 10 feet long.
MAXIMUM SPL: The loudest sound that the mic can pick up without distorting. A maximum SPL spec of 120 dB SPL is good, 130 dB SPL is very good, and 140 dB SPL or higher is excellent. 120 dB SPL is painfully loud.
SELF-NOISE: A measure of how noisy the microphone is. A self-noise spec of 25 dBA is good, 20 dBA is very good, and 15 dBA or less is excellent. A self-noise spec of 30 dB is very good if the mic is mounted directly on an instrument because the instrument’s signal is so much louder than the mic’s noise.
SIGNAL-TO-NOISE RATIO: Another measure of how noisy the microphone is. A signal-to-noise spec of 69 dB is good, 74 dB is very good, and 79 or higher is excellent. A signal-to-noise spec of 64 dB is very good if the mic is mounted directly on an instrument because the instrument’s signal is so much louder than the mic’s noise.
POWERING: Condenser microphones require special power to operate, either a battery or phantom power. Phantom power is 12 to 48 volts DC, and is supplied by a mixer or by a phantom power supply. Phantom power is sent to the mic on its mic cable; no extra wiring is needed.
CONNECTOR: An XLR or 3-pin pro audio connector is recommended to prevent hum pickup with mic cables over 10 feet long.
SIDE-ADDRESS: The microphone picks up best from its side. You aim the side of the mic at the sound source. Typical for large-diaphragm condenser mics and ribbon mics.
END-ADDRESS: The microphone picks up best from its end. You aim the end of the mic at the sound source.Typical for “pencil” or “stick” shaped mics.
Bruce Bartlett is a microphone engineer (www.bartlettaudio.com), recording engineer, and audio journalist. His latest books are “Practical Recording Techniques 6th Ed.” and “Recording Music On Location.”
Originally posted 2010-10-27 14:27:23.